Plumber's Essentials: Your Key to Installing a Bathtub
Plumber's Essentials: Your Key to Installing a Bathtub
Blog Article
This great article listed below in relation to How to Install a Bathtub Yourself is highly insightful. Read it for yourself and decide what you think about it.
Setting up a tub isn't specifically rocket science, but it does need solid plumbing, woodworking, and sometimes, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably hard task. If the old tub is easily available, the job can move immediately; if you need to open a wall surface to get rid of the old bathtub and position the new tub, the task is a lot harder. In either situation, the job is within a home handyman's abilities, although you will require a helper to vacate the old tub and embeded in the brand-new one. Ensure you have actually qualified yourself for the task and also are comfortable trying it. Instead of employing a contractor to take over a halfway-completed task, it is much better to take into consideration using one before you begin. Chances are you might need a professional plumber to make tube links.
This article will aid you install a new bathtub in your shower room if you have currently purchased a new tub as well as don't need to transform the plan of your previous water system pipes.
Your tools and also material checklist need to make up the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your setup, after that the first thing you ought to do is disconnect the water supply. After doing so, activate the taps to drain pipes any water remaining in the system. The procedure of getting rid of the existing taps can be fairly bothersome due to the limited access that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipes. Once the supply pipes have been gotten rid of, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from transforming throughout this procedure. As soon as the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any kind of old sealing compound.
Prior to proceeding to fit the new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end supplies a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the installing opening in the bath/basin making sure that the washing machines are in area between the faucet as well as the sink. Secure the faucet in place with the maker supplied backnut. When the faucet is firmly in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet ports. The previous kind needs to be linked to the faucet ends initially, tightening up just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Mounting the Bath tub
Utilizing the two wood boards under its feet, position the bathtub in the called for placement. The wooden boards are helpful in uniformly spreading the weight of the tub over the area of the boards as opposed to concentrating all the weight onto 4 small factors.
The following objective is to make sure that the tub is leveled all round. This can be attained by inspecting the spirit level and changing the feet on the bath tub till the level reads level.
To mount faucets, fit the bottom of the furthest adaptable faucet port to the ideal supply pipe by making a compression join; then do the very same for the other tap.
Turn on the water system and also check all joints and also brand-new pipework for leaks and tighten them if necessary. Fill the tub as well as likewise inspect the overflow outlet and the typical outlet for leaks.
Finally, take care of the bath paneling as described in the maker's user's manual. Tiling and also securing around the bath tub needs to wait till the tub has been used at the very least once as this will certainly settle it right into its last setting.
Preparing for the Installment
To start with, the sustaining structure provided with the bath should be fitted (if needed) according to the maker's guidelines. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to make sure that if the faucet comes with a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the taps device to avoid pressure on the bath tub.
Fit the adaptable faucet connectors to the bottom of both faucets making use of 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you utilize every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to now prepare to be suited its last position.
Tiling Around the Tub
In the area where the bath meets the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to split an inflexible seal, causing the water to permeate the wall between the bath as well as the tiling, resulting in issues with wetness as well as possible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to blend in your fixtures as well as installations. They are marketed in tubes as well as cartridges, and also are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the tub with water before securing, to enable the motion experienced when the tub remains in use. The sealer can break rather early if you do not think about this activity before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly available on the marketplace. It is advisable to fit the floor tiles using waterproof or water resistant glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I have been very excited about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I am praying you appreciated our piece. Those who enjoyed our post kindly make sure you remember to pass it around. We truly appreciate reading our article about Tools You Need to Install a New Bathtub .
Detail Report this page